2000 Ditch Witch JT 7020 Mach 1
Tri-Flo 2500 Mixing & Recycling System:
1995 Kenworth: K100E Rod Truck
1988 American Trailers, Inc Model: A455 Enclosed Trailer
Ditch Witch JT7020 Mach 1 has been completely restored over the past 6 months, we have been the owner of the drill rig and Tri-Flo 2500 Recycling System since we bought it New from the manufacturer.
Ditch Witch JT7020 Info Sheet and Package Equipment Info Below:
Displacement 436 in 3
Engine Cooling System John Deere Cool Guard 50/50 premixed coolant
Entry Angle 11°-20°
Fuel Tank Capacity 78 gal
Fuel Type Diesel
Ground Drive Speed 0-3.6 mph
Height 100.25″
Hydraulic Tank Capacity 47 gal
Joint Diameter 4″
Length 348″
Length 177.2″
Make and Model Deutz Model #BF6M1013ECP
Max Carriage Speed 185 fpm
Max Flow 160 gpm
Max Pressure 1,100 psi
Max Spindle Speed 210 rpm
Max Spindle Torque 10,000 ft/lbs
Min Bend Radius 230′
Min Bore Diameter 6″
Number of Cylinders 6
Pipe Diameter 3.62″
Pullback 70,000 lbs
Rated Engine RPM 2300 rpm
Thrust 70,000 lbs
Torque 706 ft/lbs
Weight 229 lbs
Weight 42,600 lbs
Width 103″
Ditch Witch Subsite 750 Tracker
Dimensions:
Length: 12.75 in (32.4 cm)Sub Site
Height: 31.5 in (80 cm)
Width: 6 in (15.2 cm)
Operating Weight: 5.5 lb (2.5 kg)
Operating Temperature Range: -4°F to 122°F (-20°C to 50°C)
Antenna Configuration: peak
Operating Modes:
12K beacon
29K beacon
60 Hz power
50 Hz power
8 kHz line (active)
Radio Frequencies
750 – 2
752 – 9
Maximum Locating Range:
Beacon: 0.75 ft – 99 ft 11 in (22.9 cm – 30 m)
Line: 0-10 ft (0-3 m)
Depth Calibration Tolerances * :
±4 in (10 cm) at 10 ft (3 m)
±5% from 10-20 ft (3-6.1 m)
±10% beyond 20 ft (6.1 m)
Line Location Tolerances:
Active mode: ±3% at 10 ft (3 m)
Passive mode: ±5% at 6 ft (1.8 m); ±10% at 10 ft (3 m)
Batteries: 6 C cell alkaline
Battery Life : approximately 20 hours
Battery Saver: unit shuts off after 5 minutes if no key is pressed
Tri-Flo 2500 Reclaim System:
The equipment is based upon the highly successful Tri-Flo 2500 Gallon Mud System which has the following advantages:
Main Benefits:
Cost effective method of re-cycling drilling mud’s.
Reduces cost of supplying fresh mud.
Avoids cost of disposing of liquid waste.
Cut point of 16 micron removes particles which damage triplex pumps, whilst leaving the useful
bentonite particles in suspension for re-use.
The discharge from the cleaner is virtually dry, dramatically reducing disposal costs.
Reliable and durable design, based on 20 years of field experience worldwide.
Detailed process features:
Pre-screening of the returned mud using a Tri-Flo 126 Shale Shaker.
This can handle a throughput of 350 US gpm (1300 litres/min) and is designed to remove particles down to 178 microns. The “High G” elliptical shaker action produces a virtually dry product discharged from the top of the screen.
Secondary cleaning of the returned mud using a Tri-Flo 6 x 4″ Mud Cleaner.
Tri-Flo 2500 Gal Recycling System ( Military hitch)
The mud is pumped through a bank of Tri-Flo 4″ Hydrocyclones where the larger particles are separated out by centrifugal force. The system is capable of a throughput of 350 USgpm (1300 litres/min) and is designed to remove particles down to 16 microns. The larger particles are contained within a slurry which is passed over a second Tri-Flo 126 shaker with a finer screen, which again produces a virtually dry product.
Integral mixing system using a Tri-Flo 3″ Jet Mixing Hopper.
This system allows fresh mud to be prepared very rapidly from bentonite powder. One of the three pumps is dedicated to this function allowing continuous mixing or recirculation as required. .
Large capacity storage facility.
A total of 2500 US gallons is provided, with a division separating the clean mud from the dirty mud in the ratio 60:40.
This provides the optimum balance for most drilling operations.
Integral charge pump to supply clean mud back to the drilling rig.
This provides a continuous supply of clean mud under pressure to the high pressure mud pump, avoiding problems of starvation and cavitation which can rapidly cause damage.
Specifications:
Output: Up to 350 US gpm (1300 litres/min)
Cut Point: 16 microns
Dimensions: 3500L x 2500W x 2955H
Capacity: 2500 US gallons (9,500 litres)
Pumps: Three 3 x 4″ centrifugal pumps with 22kW motors
Power: Integral control panel for all electrical functions.
Kenworth K100 Rod Truck will carry 8 full racks of 16- 15′ drill rods (Cabover Class A Truck) the truck has twin 75 gallon fuel tanks, Cummings N-14 Diesel Engine, military hitch and carries 120 – 15′ rods = 1,800′ of drill rod
American Trailer Enclosed (Class A trailer hitch) for tools and job materials
Many more photos and videos available on request.